Due to the widespread use of solar panels in order to save energy in line with the changing lifestyle, the solar panels are not known for their long-term maintenance. Fires may occur during use. One of the main causes of solar panel fires is that the charger controller used for charging is not properly installed. A charger controller is a device that controls the current when the battery is almost full. Other fire hazards include improper use of cables connected to the solar system, do not use quality copper wires. In addition to being used in conjunction with wiring harnesses, the solar panel and the positive and negative terminals of the battery are not properly secured during installation. Here is the tips How to prevent solar panel fires? - Use a controller as a proxy. - Use only the specified original wire as the input cable. - Turn off the Controller or breaker main switch when not in use. - Use a solar cable breaker to prevent fires due to overcharging of the battery. - In hot summers, use a solar wire that connects the solar panel to the battery in a heat-resistant tube.

In order for the generators in your home to be used for a long time, To be able to wake up ready when you want to use it. We will share some maintenance methods to prevent damage. ✅Service twice a year The equipment that is regularly serviced can be long resistant. Even if the generator cannot be serviced regularly, it should be serviced twice a year. ✅Check the condition of the generator A certain plug is missing, otherwise you should always check for loose threads. ✅Check and replace filters and engine oil Filters and engine oil should always be checked and replaced. For air-cooled engines, it should be replaced after driving for about 30-40 hours If the engine has a water tank, it should be changed after driving for about 100 hours. ✅Check the spark plug plates The plate should be checked and replaced once a year. ✅Start the generator engine every three months Even if you don't use the generator all the time, give it a try very three months. To let you know the condition of the generator and the sound of the machine.

Today, tiles are often used for home decoration. It is mainly used to decorate the floor and walls of the house. If tiling is not properly installed, it can cause air leaks and embossing, and if it is to be repaired, it will be time/money consuming and laborious. So, here are some dos and don'ts to be aware of when installing tiles. Level adjustment should be done when installing large tiles or rectangular tiles. 1.Level adjustment should be done when installing large tiles or rectangular tiles. 2.When gluing the tiles, you should leave a gap of about 2mm between each other. 3.Tiles of different sizes should not be mixed. 4.Only use Spin wheel (Mixer Handle) when mixing tile adhesive. 5.Use only an acid-resistant type of grout filler glue. 6.Wait about 15 minutes for the grout filling glue to dissolve. 7.By using tile adhesive, you can make the tiles air tight. A full range of tiles in various designs and sizes can be purchased at PRO 1 Global's sales centers and PRO 1 Plus (Terminal M) branch.

We need to clean our washing machines every 3 months because they can harbor bacteria. That's why we're sharing some easy ways to clean them at home. 
If you don't put clothes in the machine, pour hot water and spin it, you can prevent the growth of bacteria and mold.
 2. When cleaning the washing machine, you should open the detergent drawer/filter bag/water inlet sensor filter/washing machine lid/rubber cover at the bottom of the tub and clean it. 3. You can use hydrogen peroxide, 10% bleach, etc. to clean it. 4. You can also clean the inside and outside of the washing machine with a mixture of vinegar and baking soda and a suitable brush or toothbrush. We are sharing our knowledge to help you keep your washing machine running smoothly and prevent odors and germs from entering your machine.

Have you ever experienced a squeaking sound or tiles lifting up when you walk on them after laying new tiles? These are all problems caused by a faulty adhesive mixing system. It is very important to get the right ratio when laying tiles. The difference between a regular sand + cement mixture and a ready-made tile adhesive is - Sand + cement: It shrinks when it dries, which can cause air pockets and cracks under the tiles. Tile adhesive: It contains polymers that improve adhesion. If there is too much water, the adhesive will lose its strength and will not be able to hold the tiles together. If there is too little water, the chemical reaction will not be complete, which can cause the tiles to pop apart in a short time. The correct method is to mix the adhesive thoroughly with a machine. After mixing, leave it for 5 minutes (slaking) and then stir it again to achieve full adhesion. PRO 1 would like to recommend - 1. Red Crocodile Adhesive): Suitable for ordinary tiles and has good adhesion. 2. Crocodile Gold Grey Adhesive is specially designed for bonding large tiles (Granite/Porcelain), while Crocodile Gold White Adhesive is especially suitable for mosaic decorative tiles. During the process of bonding, separate one tile. The adhesive should be at least 90% fully adhered to the back of the tile. If it is patchy, the mixing or method is wrong.

No matter how much you clean your bathroom, you still have an unpleasant smell? This problem is usually caused by a weak exhaust system between the drain and the floor. Bad smell in the bathroom is caused by sewage gases from the drain returning to the room. It is important to know the difference between a simple PVC grate and an anti-odor floor drain. Simple PVC grate: It can only filter out dirt and hair, but cannot prevent odors and insects from entering the room. Anti-odor floor drain: It has a mechanical valve that automatically closes when there is no water or a water trap (U-Trap). Therefore, it can effectively prevent odors and insects from returning to the room. Replace bathroom floor drains with stainless steel floor drains with odor-proof systems. In addition, use odor-proof grout to prevent mold growth in the cracks between tiles. PRO 1 recommends - 1. Duss 304 Floor Drain: A high-tech drain that provides 100% odor and mold protection. 2. Sika Tile Grout (Anti-Mold): To prevent mold growth and odor between tiles, we recommend using Sika's mold-proof grout.

Are you tired of buying LED bulbs that are said to have a long lifespan but keep breaking down? The lifespan of the bulb is shortened due to the fluctuating electrical voltage and temperature. For an LED bulb to last a long time, its heat dissipation and voltage stability are key. Material Comparison - Plastic Body LED vs. Aluminum Body LED: Plastic Body: Cheaper but does not dissipate heat well. The inside of the bulb overheats and causes frequent flickering and short-circuiting. Aluminum Body: The inside of the bulb contains an Aluminum Heat Sink. Aluminum dissipates heat 60% faster than plastic, ensuring the full lifespan of the bulb. Avoid installing LED bulbs in airtight lamp housings. In areas with fluctuating electrical voltage, use voltage stabilizers to stabilize the driver circuits in the bulb. Protect. PRO 1 would like to highlight - Opple LED Bulbs are Full of light: High-quality LED chips provide full wattage light and cool light without glare. Energy-saving: Low power consumption, saving energy costs, and high heat dissipation, which also reduces the risk of burning out the bulb. Durable: Lifetime: 15,000 to 20,000 hours, so you can use it with confidence without having to replace it often. Suitable for any place: Available in various designs and watts, it can be used anywhere, such as home, office, and shop. ✨ Energy-saving + long-lasting + good light + safe Opple LED Bulb is now available for purchase.

When using an iron during the rainy season, you often encounter the problem of “sticky” bottom of your iron. Especially when ironing wet clothes, due to incorrect temperature, the remnants of the clothes can stick to the bottom of the iron. If you continue to use an iron with such sticky bottom, it will look like a stain on the clothes and may even damage the clothes. The best ways to solve the problem of sticky bottom of the iron Clean the iron with a soft cloth after it has cooled down. Mix baking soda with a little water and rub it gently. Avoid ironing clothes that are still wet. Adjust the temperature according to the type of clothes. In addition, the Soleplate Coating is also important when choosing an iron. Ceramic Coating -Smooth movement. -Low stickiness. -Convenient for daily use. Non-Stick Coating -Clothes don't stick easily. -Easy to clean. -Easy to use. Stainless Steel Soleplate -Good heat distribution. -Durable. -Long-lasting. When buying an iron, you should also look at the type of Soleplate Coating in addition to Watt. Choosing a good iron in the rain will keep your clothes neat and beautiful and make it more convenient for daily use.

Are you tired of having to deal with water in your home every time it rains? A leaky roof can not only damage your roof but also cause electrical hazards. The main causes of roof leaks are — - Cracks in the roof tiles - Cracks in the gutters So, before the rain starts, you should check them in advance and protect them with these 5 tips. 1. Patch the roof tiles and cracks with Bitumen Tape Just stick bitumen tape on the small cracks in the roof tiles and roof tiles to immediately reduce water leakage. 2. Use Acrylic Waterproofing For concrete roofs (Slabs) and gutters, waterproofing is more reliable. 3. Replace worn screws Use new screws with EPDM rubber seals to reduce water infiltration. 4. Remove rust and dust Before applying the sealant, clean the surface with a wire brush. No matter how good the sealant is, if the surface is not clean, it will come off after a while. 5. Only apply when the surface is completely dry Applying tape or painting while it is wet can weaken the adhesion. If you are using tape, press it firmly with your hands or a roller to prevent air bubbles from forming in the tape. If you apply it in the sun (when the surface is hot), the tape will be softer and more durable. When applying the sealant, it is better to apply it in at least (2) coats, not in one coat. Wait for the first coat to dry completely (at least 4 to 6 hours). When painting the second floor, paint it crosswise (in the same direction as the first floor). This will ensure a thicker and safer finish. Products recommended by PRO 1 -Sika Multiseal Gray(100mmx3m) -Crocodile Roof Shield Water Proofing Pre-treatment before the rain can help protect your home from water leaks .

During the rainy season, the air becomes humid, so your bedding, pillows, and blankets tend to smell musty and musty. These smells can cause sleeplessness and shortness of breath, so you should definitely do these few things. 1. Dry your pillow in the sun regularly The sun reduces humidity and naturally eliminates bacteria and mold. 2. Wash your pillow cover once a week You need to clean it regularly to prevent sweat, dust, and oil from accumulating. 3. Keep your room well-ventilated Rooms with poor air flow are the easiest places for mold to grow. 4. Sprinkle baking soda on it to absorb the odor If you clean it for 15–30 minutes, the odor will be significantly reduced. 5. Keep a Charcoal Bag / Moisture Absorber These are very useful items during the rainy season as they absorb moisture. A clean and fresh bedroom will help you sleep better and is also good for your health.